Positek

E603

Part no.: E603

Key Features

• Single axis

• Up to 160°

• Voltage or Current interface

• IP67

The intrinsically safe E603 is ATEX and IECEx approved for use in potentially explosive gas/vapour and dust atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

The E603, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees and with full EMC protection built in. The sensor provides a linear output characteristic with angle of deflection. There is a machined registration mark to identify the calibrated mid point.
Overall performance, repeatability and stability are outstanding over a wide temperature range. Electrical connections to the sensor are made via an industrial standard 4-pin M12 connector, with limited rotational capability to facilitate cable routing. The sensor has a rugged stainless steel body and mounting flange. The flange has two 4.5mm by 30 degree wide slots on a 48mm pitch to simplify mounting and position adjustment. Environmental sealing is to IP67.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at

"*" indicates required fields

Hi, My name is

and I’m interested in the

You can reach me by email at

or phone at

Message

This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

X111

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M8 Rod Eyes, Body Clamps or M8 ThreadsSpring loaded pushrod option available
  • Available in any measurement range from 0-5mm to 0-800mm
  • Sealed to IP65/67 depending on connector/cable option

Positek

M101

  • ATEX/IECEx approved for mining
  • Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
  • Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
  • Sealed to IP65/67 depending on connector/cable option

Positek

E117

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
  • Available in any measurement range from 0-5mm to 0-350mm
  • Sealed to IP67

Positek

P100

  • Body Diameter: 35mm
  • Sensor Mounting: In-Cylinder Mounting
  • Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
  • IP65 (connector) / IP67 (cable)
Blog:

NEW PRODUCT – VLH-35 ELECTRIC ENCODER FOR DC SERVO MOTORS

Netzer Precision Position Sensors is introducing the VLH-35, a new product designed to meet the needs of the servo motor industry and its requirements for the next generation of industrial rotary motion control.

Everight Position’s Submersible Sensors for UUVs

While they may be small, the role of rotary encoders in spacecraft is vital, demanding a balance between performance, reliability, and the unforgiving environment of space. From NASA’s Robonaut II to automated material handling systems on the International Space Station, Everight has worked with engineers to put rotary encoders into ‘the final frontier.’

Seeing Is Believing: POSITAL 3D drawings now available for millions of encoders

POSITAL’s product finder has generated full specification custom datasheets for years. Rather than having to guess on specifications from a confusing product configurator, POSITAL provides part specific datasheets in real time for the given part number of interest.

Sensors As Tough as You Are

If your environment is dirty, hot, wet, or corrosive your requirements may have some similarities with that of the construction industry.

Download Now

This field is for validation purposes and should be left unchanged.