Positek

M603

Part no.: M603

Key Features

• Single axis

• Up to 160°

• Voltage or Current interface

• IP67

 

The intrinsically safe M603 is ATEX and IECEx approved for use in potentially explosive gas/vapour, dust atmospheres and mining environments.

It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

The M603, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees and with full EMC protection built in. The sensor provides a linear output characteristic with angle of deflection. There is a machined registration mark to identify the calibrated mid point.

Overall performance, repeatability and stability are outstanding over a wide temperature range. Electrical connections to the sensor are made via an industrial standard 4-pin M12 connector, with limited rotational capability to facilitate cable routing. The sensor has a rugged stainless steel body and mounting flange. The flange has two 4.5mm by 30 degree wide slots on a 48mm pitch to simplify mounting and position adjustment. Environmental sealing is to IP67.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Drawing Download

Call us for more info at

"*" indicates required fields

Hi, My name is

and I’m interested in the

You can reach me by email at

or phone at

Message

This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

E114

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M5 rod eyes, body clamps or M5 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800mm
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Positek

X125

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800mm
  • Sealed to IP68 350bar, 3500msw, 5000psi

Positek

P101

  • Body Diameter: 35mm
  • Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
  • Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
  • Sealed to IP65/67 depending on connector/cable option

Positek

X115

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800m
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)
Blog:

Inductosyn: End of an Era, New Opportunities or Both?

Recently, obtaining the Inductosyn and components for maintenance has become more difficult. For decades the Inductosyn from Farrand Controls / Ruhle Companies sat near the top of the rotary sensor hierarchy. Providing sub 2 arcsec (0.5 mdeg) accuracies, it combined the robustness of a resolver with the performance of the best optical encoders. Despite its shortcomings, it found plenty of customers, from airborne infrared and radar systems, to telescopes, satellite communication antennae (SATCOM), machine tooling and low-pressure vacuum chambers.

TMR: A New Revolution in Magnetic Rotary Encoders

Abstract: Tunnel magnetoresistance (TMR) sensing is an exciting new chapter for magnetic-based rotary encoders. Requiring less current, while offering higher signal strength, many of the inherent short comings of Hall Effect based sensors can be addressed.

SSI Hardware

SSI hardware is fairly simple. Just use any RS-422 transceiver to generate the differential signals from/to the microcontroller port pins. Keep reading to learn about the different implementations of SSI hardware.

‘Dirty Deeds Done Dirt Cheap’ – The Gill Blade Sensor

Not all sensors live easy lives. While some will go on to do noble things such as aiding in medical surgery robotics or will find lives in cutting-edge cobots such as Boston Dynamic’s spot, others will live simpler, yet equally important lives, this article is dedicated to one of those unsung heroes, the Gill Blade Sensor.

Download Now

This field is for validation purposes and should be left unchanged.