Positek

H603

Part no.: H603

Key Features

• Single axis

• Up to 160°

• Voltage or Current interface

• IP67

Intrinsically safe H603 is CSA approved for use in potentially explosive dust and gas/vapour atmospheres. The H603 is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

The H603, like all Positek® sensors, is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees and with full EMC protection built in. The sensor provides a linear output characteristic with angle of deflection. There is a machined registration mark to identify the calibrated mid point.

Overall performance, repeatability and stability are outstanding over a wide temperature range. Electrical connections to the sensor are made via an industrial standard 4-pin M12 connector, with limited rotational capability to facilitate cable routing.

The sensor has a rugged stainless steel body. The flange has two 4.5mm by 30 degree wide slots on a 48mm pitch to simplify mounting and position adjustment. Environmental sealing is to IP67.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (G005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Drawing Download

Call us for more info at

"*" indicates required fields

Hi, My name is

and I’m interested in the

You can reach me by email at

or phone at

Message

This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

Positek X500

  • ATEX/IECE: Ex II 1G; Ex ia IIC T4 GA
  • 0.5-9.5V or 4-20mA outputs
  • ATEX variants of P502, P505 and P520 available
  • Up to 160 deg range

Positek

M133

  • ATEX/IECEx approved for mining
  • Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
  • Available in any measurement range from 0-51mm to 0-100mm(for 2-50mm range see P103)
  • Sealed to IP65/67 depending on connector/cable option

Positek

G133

  • CSA approved to: Class I, Zone 0
  • Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
  • Available in any measurement range from 0-51mm to 0-100mm(for 2-50mm range see P103)
  • Sealed to IP65/67 depending on connector/cable option

Positek

M103

  • ATEX/IECEx approved for mining
  • Sensor Mounting: Flange or Body ClampsSpring loaded pushrod option available
  • Available in any measurement range from  0-2mm to 0-50mm (for 51-100mm range see P133)
  • Sealed to IP65/67 depending on connector/cable option
Blog:

NASA Lunabotics Challenge

Nearly fifty University Teams recently gathered in Florida for the NASA Lunabotics Challenge. The robots are tasked with driving, digging, and depositing regolith—the fragmented rock material that covers the moon’s surface—in a lunar simulant. Beyond robotics and mechatronics, the program teaches team work, project management and industry collaboration.

Inductosyn: End of an Era, New Opportunities or Both?

Recently, obtaining the Inductosyn and components for maintenance has become more difficult. For decades the Inductosyn from Farrand Controls / Ruhle Companies sat near the top of the rotary sensor hierarchy. Providing sub 2 arcsec (0.5 mdeg) accuracies, it combined the robustness of a resolver with the performance of the best optical encoders. Despite its shortcomings, it found plenty of customers, from airborne infrared and radar systems, to telescopes, satellite communication antennae (SATCOM), machine tooling and low-pressure vacuum chambers.

Netzer VLX

Encoders that perform in the most important application: Yours!

Encoder Technology Overview

Rotary encoders are used in a variety of applications to provide feedback on position, speed, direction, or angle. There are several different encoder types…

Download Now

This field is for validation purposes and should be left unchanged.