E130

Positek

Part no.: E130

Key Features

• ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)

• Sensor Mounting: In-cylinder

• Available in any measurement range from 0-400mm to 0-1485mm

• Sealed to IP65/67 depending on connector/cable option

The intrinsically safe E130 is ATEX and IECEx approved for use in potentially explosive gas/vapour and dust atmospheres. It is designed for demanding hydraulic or pneumatic cylinder position feedback applications where service life, environmental resistance and cost are important and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

Overall performance, repeat-ability and stability are outstanding over a wide temperature range. The unit is highly compact and space-efficient, being responsive along almost its entire length. Like all Positek sensors, the E130 provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-400mm to 0-1485mm and with full EMC protection built in.

The sensor is very rugged, being made of stainless steel with an inert fluoropolymer-sheathed probe and stainless steel target tube. The sensor is easy to install in cylinders and has a wide range of mechanical options. Environmental sealing is to IP65 or IP67 depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

You may also be interested in:

Positek

Positek P500

35mm diameter body
Analog voltage and current outputs
Up to 0.1% linearity
16-160 deg range; for <16 deg see P502

Positek

P117

Body Diameter: 19mm
Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
Available in any measurement range from 0-5mm to 0-350mm
Sealed to IP67

Positek

M100

ATEX/IECEx approved for mining
Sensor Mounting: In-Cylinder Mounting
Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
IP65 (connector) / IP67 (cable)

Positek

M101

ATEX/IECEx approved for mining
Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
Sealed to IP65/67 depending on connector/cable option

Custom-Off-The-Shelf: The New ‘COTS’ Goods

For decades there has been an initiative to source COTS (Commercial-off-the-shelf) goods when possible, and for good reason. COTS goods generally are less expensive, more readily available and easier to dual source.

MEMS Inclinometer Specifications

Inclinometers, also called tilt sensors, clinometers, or slope sensors, are designed to measure the angle of an object with respect to the force of gravity. These tilt or level meters determine the pitch and/or roll angle and output these values via the appropriate electrical interface.

Robust IncOders that Are Right for Your Application

Zettlex IncOders are non-contact devices for precision angle measurement. They work like a transformer, using an inductive technique. IncOders may be considered as an inductive angle encoder. IncOders are ideally suited to harsh environments – where potentiometers, optical or capacitive devices may prove unreliable.

Technical Note: Intrinsically Safe vs. Inherently Safe Sensors

Intrinsically safe (IS) sensors are designed to operate safely in hazardous areas where there is a risk of explosion. IS sensors limit the amount of electrical and thermal energy that can be released in the event of a fault, to a level below that which is capable of igniting flammable gases, vapors, or dust.