Positek

E114

Part no.: E114

Key Features

• ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)

• Sensor Mounting: M5 rod eyes, body clamps or M5 threadsSpring loaded pushrod option available

• Available in any measurement angle from 0-5mm to 0-800mm

• Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

The intrinsically safe 10 bar E114 is an ATEX and IECEx approved affordable, durable, high-accuracy position sensor.

The E114, like all Positek sensors, provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in. The sensor is very robust, the body and push rod being made of stainless steel for long service life and environmental resistance. Derived from the popular E101, the E114 has been designed for applications where the sensor may be completely submerged in water up to a pressure of 10Bar, but good sensor performance and cost are still important.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier. Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

Hi, My name is

and I’m interested in the

You can reach me by email at

or phone at

Message

This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

Positek S520

  • Subsea encoder to 350Bar, 5000 psi
  • Analog voltage and current outputs
  • Up to 0.1% linearity
  • Measure up to 100 deg range

Positek

Positek E500

  • ATEX/IECEx for gas/vapor and dust
  • 0.5-9.5V or 4-20mA outputs
  • ATEX variants of P502 & P505 available
  • Up to 160 deg range

Positek

P603

  • Single axis
  • Up to 160°
  • Voltage, Current or Ratiometric interface
  • IP67

Positek

X130

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: In-cylinder
  • Available in any measurement range from 0-400mm to 0-1485mm
  • Sealed to IP65/67 depending on connector/cable option
Blog:

‘Dirty Deeds Done Dirt Cheap’ – The Gill Blade Sensor

Not all sensors live easy lives. While some will go on to do noble things such as aiding in medical surgery robotics or will find lives in cutting-edge cobots such as Boston Dynamic’s spot, others will live simpler, yet equally important lives, this article is dedicated to one of those unsung heroes, the Gill Blade Sensor.

POSITAL UCD…H200 Through-hole Encoder

Over the past 15 years Everight Position has worked with a lot of unique sensors. But one of our favorites is the POSITAL UCD…H200. When looking back there are two things that make this sensor so special.

TMR: A New Revolution in Magnetic Rotary Encoders

Abstract: Tunnel magnetoresistance (TMR) sensing is an exciting new chapter for magnetic-based rotary encoders. Requiring less current, while offering higher signal strength, many of the inherent short comings of Hall Effect based sensors can be addressed.

Osico Oil-Mon: The Ultimate Oil Quality Sensor for Real-Time Monitoring

In the world of industrial machinery and high-tech equipment, maintaining optimal lubrication is not just a matter of efficiency—it’s a necessity for reliability and longevity. Particle contamination, water intrusion, and oxidation can transform lube oil from a machine’s lifeblood into its most insidious foe. While periodic lab analyses provide snapshots of oil health, imagine the possibilities if these critical parameters could be monitored continuously, in real time.

Complete Posital Product Line

Click Here

Everight Position is dedicated to helping customers find the best solution for their positioning needs.™

©2020, Everight Position  |  Terms & Conditions

Speak directly to one of our experts! We’d love to hear all about your project and determine how Everight can help.

856-727-9500

Email: info@evrtp.com