X101

Positek

Part no.: X101

Key Features

• ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)

• Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available

• Any stroke from 0-5mm to 0-800mm (e.g. 305mm)

• Sealed to IP65/67 depending on connector/cable option

The intrinsically safe X101 is ATEX and IECEx approved for use in potentially explosive gas/vapour atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas. The unit is highly compact and space-efficient, being responsive along almost its entire length.

The X101, like all Positek sensors, provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in. The sensor is very robust, the body and push rod being made of stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with mounting options including M5 rod eye bearings and body clamps. The push rod can be supplied free or captive, with female M5 thread, an M5 rod eye, or dome end, Captive push rods can be sprung loaded, in either direction, on sensors up to 300mm of travel. Environmental sealing is to IP65 or IP67, depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

You may also be interested in:

Positek

E133

ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
Available in any measurement range from 0-51mm to 0-100mm(for 2-50mm range see P103)
Sealed to IP65/67 depending on connector/cable option

Positek

Positek E500

ATEX/IECEx for gas/vapor and dust
0.5-9.5V or 4-20mA outputs
ATEX variants of P502 & P505 available
Up to 160 deg range

Positek

S125

Body Diameter: 40mm
Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
Available in any measurement angle from 0-5mm to 0-800mm
Sealed to IP68 350bar, 3500msw, 5000psi

Positek

M115

ATEX/IECEx approved for mining
Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
Available in any measurement angle from 0-5mm to 0-800m
Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Hydraulic Cylinder Position Sensor Applications

Positek supplies a range of hydraulic cylinder position sensors that offer high-precision position monitoring in harsh environments such as industrial machinery…

Spine Surgery Robot

Spinal surgery robot with advanced robotic guided technologies supports high requirements of predictable surgical procedures.

Technical Note: Intrinsically Safe vs. Inherently Safe Sensors

Intrinsically safe (IS) sensors are designed to operate safely in hazardous areas where there is a risk of explosion. IS sensors limit the amount of electrical and thermal energy that can be released in the event of a fault, to a level below that which is capable of igniting flammable gases, vapors, or dust.

Why Holistic Encoders are More Accurate

All absolute rotary encoders have a rotor which is attached to the rotating shaft and a stator which is attached to the housing holding the shaft. The interaction of these two components produces a measure of the shafts rotational angle. The most important parameters of absolute rotary sensors are resolution, accuracy and tolerance to misalignment of the rotational axes.