Positek

X106

Part no.: X106

Key Features

• ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)

• Sensor Mounting: In-cylinder

• Available in any measurement range from 0-5mm to 0-800mm

• Sealed to IP65/67 depending on connector/cable option

The intrinsically safe X106 is ATEX and IECEx approved for use in potentially explosive gas/vapour atmospheres. It is designed for demanding hydraulic or pneumatic cylinder position feedback applications where service life, environmental resistance and cost are important and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The unit is highly compact and space-efficient, being responsive along almost its entire length. Like all Positek sensors it provides a linear output proportional to displacement, each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in.

The X106 is very rugged, being made of stainless steel with an inert fluoropolymer-sheathed probe and stainless steel target tube. The probe and target are easy to install, as is the electronics module which has a two mounting options. Environmental sealing is to IP65 or IP67 depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

Hi, My name is

and I’m interested in the

You can reach me by email at

or phone at

Message

This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

E115

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800m
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Positek

M103

  • ATEX/IECEx approved for mining
  • Sensor Mounting: Flange or Body ClampsSpring loaded pushrod option available
  • Available in any measurement range from  0-2mm to 0-50mm (for 51-100mm range see P133)
  • Sealed to IP65/67 depending on connector/cable option

Positek

M100

  • ATEX/IECEx approved for mining
  • Sensor Mounting: In-Cylinder Mounting
  • Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
  • IP65 (connector) / IP67 (cable)

Positek

G118

  • CSA approved to: Class I, Zone 0
  • Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
  • Available in any measurement range from 0-2mm to 0-50mm(for 51-100mm range see P138)
  • Sealed to IP67
Blog:

TMR: A New Revolution in Magnetic Rotary Encoders

Abstract: Tunnel magnetoresistance (TMR) sensing is an exciting new chapter for magnetic-based rotary encoders. Requiring less current, while offering higher signal strength, many of the inherent short comings of Hall Effect based sensors can be addressed.

Everight Position: Leading the Way in Hazardous Environment Solutions

Everight Position provides solutions tailored for hazardous environments. With our focus on customer well-being and reliability, we’re committed to equipping industries with sensors that are compliant to regulatory requirements.

How-to: 2 Point Operation of an Open Collector Switch Output

In this example, the switch point has been set to ‘Full Alarm’. By setting the switch point to 90% with an 80% hysteresis, the switch will come on at 90% and switch off at 10%.

Why Holistic Encoders are More Accurate

All absolute rotary encoders have a rotor which is attached to the rotating shaft and a stator which is attached to the housing holding the shaft. The interaction of these two components produces a measure of the shafts rotational angle. The most important parameters of absolute rotary sensors are resolution, accuracy and tolerance to misalignment of the rotational axes.

Complete Posital Product Line

Click Here

Everight Position is dedicated to helping customers find the best solution for their positioning needs.™

©2020, Everight Position  |  Terms & Conditions

Speak directly to one of our experts! We’d love to hear all about your project and determine how Everight can help.

856-727-9500

Email: info@evrtp.com