X114

Positek

Part no.: X114

Key Features

• ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)

• Sensor Mounting: M5 rod eyes, body clamps or M5 threadsSpring loaded pushrod option available

• Available in any measurement angle from 0-5mm to 0-800mm

• Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

The intrinsically safe 10 bar X114 is an ATEX and IECEx approved affordable, durable, high-accuracy position sensor.

The X114, like all Positek sensors, provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in. The sensor is very robust, the body and push rod being made of stainless steel for long service life and environmental resistance. Derived from the popular X101, the X114 has been designed for applications where the sensor may be completely submerged in water up to a pressure of 10Bar, but good sensor performance and cost are still important.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier. Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

You may also be interested in:

Positek

H133

CSA approved to: Class I, Zone 0
Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
Available in any measurement range from 0-51mm to 0-100mm(for 2-50mm range see P103)
Sealed to IP65/67 depending on connector/cable option

Positek

S115

Body Diameter: 35mm
Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
Available in any measurement angle from 0-5mm to 0-800m
Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Positek

E130

ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
Sensor Mounting: In-cylinder
Available in any measurement range from 0-400mm to 0-1485mm
Sealed to IP65/67 depending on connector/cable option

Positek

H130

CSA approved to: Class I, Zone 0
Sensor Mounting: In-cylinder
Available in any measurement range from 0-400mm to 0-1485mm
Sealed to IP65/67 depending on connector/cable option

The NEXTGen CANopen inclinometers

The NEXTGen CANopen inclinometers are available now! POSITAL has updated its family of TILTIX inclinometers with new three-axis MEMS accelerometers, enhanced firmware, and a new housing concept.

Seeing Is Believing: POSITAL 3D drawings now available for millions of encoders

POSITAL’s product finder has generated full specification custom datasheets for years. Rather than having to guess on specifications from a confusing product configurator, POSITAL provides part specific datasheets in real time for the given part number of interest.

SSI Hardware

SSI hardware is fairly simple. Just use any RS-422 transceiver to generate the differential signals from/to the microcontroller port pins. Keep reading to learn about the different implementations of SSI hardware.

Position Sensors for Hazardous Locations

When choosing components for a hazardous environment it is important to have a trusted partner. For over a decade engineers have relied on Everight Position for rotary, linear and tilt sensors for these challenging applications.