Positek

X130

Part no.: X130

Key Features

• ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)

• Sensor Mounting: In-cylinder

• Available in any measurement range from 0-400mm to 0-1485mm

• Sealed to IP65/67 depending on connector/cable option

The intrinsically safe X130 is ATEX and IECEx approved for use in potentially explosive gas/vapour atmospheres. It is designed for demanding hydraulic or pneumatic cylinder position feedback applications where service life, environmental resistance and cost are important and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

Overall performance, repeat-ability and stability are outstanding over a wide temperature range. The unit is highly compact and space-efficient, being responsive along almost its entire length. Like all Positek sensors, the X130 provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-400mm to 0-1485mm and with full EMC protection built in.

The sensor is very rugged, being made of stainless steel with an inert fluoropolymer-sheathed probe and stainless steel target tube. The sensor is easy to install in cylinders and has a wide range of mechanical options. Environmental sealing is to IP65 or IP67 depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

Hi, My name is

and I’m interested in the

You can reach me by email at

or phone at

Message

This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

G100

  • CSA approved to: Class I, Zone 0
  • Sensor Mounting: In-Cylinder Mounting
  • Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
  • IP65 (connector) / IP67 (cable)

Positek

X117

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
  • Available in any measurement range from 0-5mm to 0-350mm
  • Sealed to IP67

Positek

M112

  • ATEX/IECEx approved for mining
  • Sensor Mounting: 1/2" UNF ThreadSpring loaded plunger
  • Available in any measurement range from 0-5mm to 0-50mm
  • Sealed to IP67

Positek

G114

  • CSA approved to: Class I, Zone 0
  • Sensor Mounting: M5 rod eyes, body clamps or M5 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800mm
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)
Blog:

Intrinsically Safe Absolute Rotary Encoders

In the most hazardous environments, where an explosive atmosphere consisting of flammable gas or vapor is regularly present and a sensor fault cannot be risked, Intrinsically Safe (IS) sensors may be the best sensing option. Generally, these sensors are paired with a barrier which limits the amount of electrical and thermal energy that can enter the Hazardous Area to an amount that is so small that even in the situation of a sensor fault, there is not enough energy to cause an ignition.

How-to: 2 Point Operation of an Open Collector Switch Output

In this example, the switch point has been set to ‘Full Alarm’. By setting the switch point to 90% with an 80% hysteresis, the switch will come on at 90% and switch off at 10%.

Liquid Level Sensor Interface

Enhancing Precision in Liquid Level Measurement with GS Liquid Level Software Introduction Accurate liquid level sensing is an important parameter in many processes, such as those involving specific gravity and identifying emulsion layers. The GS Liquid Level software, designed to work seamlessly with Gill Liquid Level sensors, is a revolutionary tool for engineers and system […]

Seeing Is Believing: POSITAL 3D drawings now available for millions of encoders

POSITAL’s product finder has generated full specification custom datasheets for years. Rather than having to guess on specifications from a confusing product configurator, POSITAL provides part specific datasheets in real time for the given part number of interest.

Complete Posital Product Line

Click Here

Everight Position is dedicated to helping customers find the best solution for their positioning needs.™

©2020, Everight Position  |  Terms & Conditions

Speak directly to one of our experts! We’d love to hear all about your project and determine how Everight can help.

856-727-9500

Email: info@evrtp.com