Positek

M101

Part no.: M101

Key Features

• ATEX/IECEx approved for mining

• Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available

• Any stroke from 0-5mm to 0-800mm (e.g. 305mm)

• Sealed to IP65/67 depending on connector/cable option

The intrinsically safe M101 is ATEX and IECEx approved for use in potentially explosive gas/vapour, dust atmospheres and mining environments. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas. The unit is highly compact and space-efficient, being responsive along almost its entire length.

The M101, like all Positek sensors, provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in. The sensor is very robust, the body and push rod being made of stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with mounting options including M5 rod eye bearings and body clamps. The push rod can be supplied free or captive, with female M5 thread, an M5 rod eye, or dome end, Captive push rods can be sprung loaded, in either direction, on sensors up to 300mm of travel. Environmental sealing is to IP65 or IP67, depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

Hi, My name is

and I’m interested in the

You can reach me by email at

or phone at

Message

This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

Positek P500

  • 35mm diameter body
  • Analog voltage and current outputs
  • Up to 0.1% linearity
  • 16-160 deg range; for <16 deg see P502

Positek

S114

  • Body Diameter: 35mm
  • Sensor Mounting: M5 rod eyes, body clamps or M5 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800mm
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Positek

P118

  • Body Diameter: 19mm
  • Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
  • Available in any measurement range from 0-2mm to 0-50mm(for 51-100mm range see P138)
  • Sealed to IP67

Positek

M115

  • ATEX/IECEx approved for mining
  • Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800m
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)
Blog:

Technical Note: Intrinsically Safe vs. Inherently Safe Sensors

Intrinsically safe (IS) sensors are designed to operate safely in hazardous areas where there is a risk of explosion. IS sensors limit the amount of electrical and thermal energy that can be released in the event of a fault, to a level below that which is capable of igniting flammable gases, vapors, or dust.

Miniature Kit Encoders Ensure High Performance in Maxon Micromotors

With the increasing sophistication of electronic controls for mechanical systems, there is more demand for durable, accurate and easy to use displacement sensors. As automation becomes more common there is also an increasing sensitivity to price. Customers also want sensors that can be easily connected and mechanically integrated.

Implementation of SSI Interface

Synchronous Serial Interface (SSI) is a widely used serial interface standard for industrial applications especially, rotary encoders. It is a point-to-point connection from a master (e.g. PLC, microcontroller or other control systems) to a slave (e.g. the rotary encoder).

How To: Use an Open Collector Output

All new Gill level sensors come with a secondary output function which operates as a high or low level switch. So what is it and how do I use an Open Collector switch output?

Complete Posital Product Line

Click Here

Everight Position is dedicated to helping customers find the best solution for their positioning needs.™

©2020, Everight Position  |  Terms & Conditions

Speak directly to one of our experts! We’d love to hear all about your project and determine how Everight can help.

856-727-9500

Email: info@evrtp.com