G117

Positek

Part no.: G117

Key Features

• CSA approved to: Class I, Zone 0

• Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available

• Available in any measurement range from 0-5mm to 0-350mm

• Sealed to IP67

The intrinsically safe G117 is CSA approved for use in potentially explosive gas/vapour atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The unit is very compact and space-efficient with a small 19mm diameter body. The sensor is very robust, the body and push rod being made of stainless steel. The sensor is easy to install with mounting options including M5 male stud and M5 rod eye bearing. The push rod can be supplied free or captive, with male M5 thread or M5 rod eye. Like all Positek sensors, the G117 provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-350mm and with full EMC protection built in. The G117 offers a range of mechanical options, environmental sealing is to IP67.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (G005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

You may also be interested in:

Positek

H133

CSA approved to: Class I, Zone 0
Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
Available in any measurement range from 0-51mm to 0-100mm(for 2-50mm range see P103)
Sealed to IP65/67 depending on connector/cable option

Positek

X005

Provides isolation between the amplifier power supply, the hazardous area and the X005 output signal
Input power supply range of 12 to 30 volts DC
Factory configured to either 0.5 to 9.5V or 4-20mA
Bandwidth of 4.7kHz, making it ideal for servo control loops.

Positek

E101

ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
Sealed to IP65/67 depending on connector/cable option

Positek

X125

ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
Available in any measurement angle from 0-5mm to 0-800mm
Sealed to IP68 350bar, 3500msw, 5000psi

Position Sensors for Hazardous Locations

When choosing components for a hazardous environment it is important to have a trusted partner. For over a decade engineers have relied on Everight Position for rotary, linear and tilt sensors for these challenging applications.

Technical Note: Intrinsically Safe vs. Inherently Safe Sensors

Intrinsically safe (IS) sensors are designed to operate safely in hazardous areas where there is a risk of explosion. IS sensors limit the amount of electrical and thermal energy that can be released in the event of a fault, to a level below that which is capable of igniting flammable gases, vapors, or dust.

Spine Surgery Robot

Spinal surgery robot with advanced robotic guided technologies supports high requirements of predictable surgical procedures.

POSITAL UCD…H200 Through-hole Encoder

Over the past 15 years Everight Position has worked with a lot of unique sensors. But one of our favorites is the POSITAL UCD…H200. When looking back there are two things that make this sensor so special.