Positek

H101

Part no.: H101

Key Features

• CSA approved to: Class I, Zone 0

• Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available

• Any stroke from 0-5mm to 0-800mm (e.g. 305mm)

• Sealed to IP65/67 depending on connector/cable option

The intrinsically safe H101 is CSA approved for use in potentially explosive gas/vapour and dust atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas. The unit is highly compact and space-efficient, being responsive along almost its entire length.

The H101, like all Positek sensors, provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in. The sensor is very robust, the body and push rod being made of stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with mounting options including M5 rod eye bearings and body clamps. The push rod can be supplied free or captive, with female M5 thread, an M5 rod eye, or dome end, Captive push rods can be sprung loaded, in either direction, on sensors up to 300mm of travel. Environmental sealing is to IP65 or IP67, depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (G005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at

"*" indicates required fields

Hi, My name is

and I’m interested in the

You can reach me by email at

or phone at

Message

This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

X130

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: In-cylinder
  • Available in any measurement range from 0-400mm to 0-1485mm
  • Sealed to IP65/67 depending on connector/cable option

Positek

S125

  • Body Diameter: 40mm
  • Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800mm
  • Sealed to IP68 350bar, 3500msw, 5000psi

Positek

E101

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
  • Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
  • Sealed to IP65/67 depending on connector/cable option

Positek

G005

  •  Provides isolation between the amplifier power supply, the hazardous area and the G005 output signal
  • Input power supply range of 12 to 30 volts DC
  • Factory configured to either 0.5 to 9.5V or 4-20mA
  •  Bandwidth of 4.7kHz, making it ideal for servo control loops.
Blog:

Application Note: Rotary Encoders for Azimuth and Elevation Feedback in Vision Gimbals

Vision gimbals are critical components in various applications, including unmanned aerial vehicles (UAVs), robotics, and surveillance systems. Used in IR, LIDAR, visible light and other frequencies, they stabilize cameras or sensors, providing smooth and accurate footage or data acquisition regardless of platform movement.

Facing the Inevitable: Sensor Obsolescence, Mitigation Strategies, and Alternatives

Obsolescence. If its only difficulty was remembering how it is spelled it wouldn’t be so bad. And whether you’re trying to replace a sensor that has failed with age or are a manufacturer who can no longer source an important sensor, obsolescence of an inexpensive sensor can create extremely expensive headache. At Everight Position we help customers to understand the causes of sensor obsolescence, explore mitigation strategies and find alternative solutions.

Seeing Is Believing: POSITAL 3D drawings now available for millions of encoders

POSITAL’s product finder has generated full specification custom datasheets for years. Rather than having to guess on specifications from a confusing product configurator, POSITAL provides part specific datasheets in real time for the given part number of interest.

The NEXTGen CANopen inclinometers

The NEXTGen CANopen inclinometers are available now! POSITAL has updated its family of TILTIX inclinometers with new three-axis MEMS accelerometers, enhanced firmware, and a new housing concept.

Download Now

This field is for validation purposes and should be left unchanged.