X603

Positek

Part no.: X603

Key Features

• Single axis

• Up to 160°

• Voltage or Current interface

• IP67

The intrinsically safe X603 tilt sensor is ATEX and IECEx approved for use in potentially explosive gas/vapour atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas. The X603, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees and with full EMC protection built in. The sensor provides a linear output characteristic with angle of deflection. There is a machined registration mark to identify the calibrated mid point.

Overall performance, repeatability and stability are outstanding over a wide temperature range. Electrical connections to the sensor are made via an industrial standard 4-pin M12 connector, with limited rotational capability to facilitate cable routing.

The sensor has a rugged stainless steel body and anodised aluminium mounting flange. The flange has two 4.5mm by 30 degree wide slots on a 48mm pitch to simplify mounting and position adjustment. Environmental sealing is to IP67.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

You may also be interested in:

Positek

G114

CSA approved to: Class I, Zone 0
Sensor Mounting: M5 rod eyes, body clamps or M5 threadsSpring loaded pushrod option available
Available in any measurement angle from 0-5mm to 0-800mm
Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Positek

P101

Body Diameter: 35mm
Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
Sealed to IP65/67 depending on connector/cable option

Positek

X101

ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
Sealed to IP65/67 depending on connector/cable option

Positek

X118

ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
Available in any measurement range from 0-2mm to 0-50mm(for 51-100mm range see P138)
Sealed to IP67

TMR: A New Revolution in Magnetic Rotary Encoders

Abstract: Tunnel magnetoresistance (TMR) sensing is an exciting new chapter for magnetic-based rotary encoders. Requiring less current, while offering higher signal strength, many of the inherent short comings of Hall Effect based sensors can be addressed.

Tiny Tech, Big Impact: Rotary Encoders Are a Critical Link the Agrobot Revolution

A recent GlobalData report highlights the impressive growth of the robotics industry in agriculture (reaching $218 billion by 2030), a key component behind this revolution often goes unnoticed: the rotary encoder. These unsung heroes convert rotational motion into precise electrical signals, playing a vital role in ensuring the smooth, accurate movements of agricultural robots.

Introduction to Intrinsically Safe Sensors

Intrinsically safe (IS) sensors are unable to produce a spark strong enough to cause ignition. Learn how this is accomplished and design considerations when using IS sensors.

NetzerUSA.com – Your Resource for Innovative Rotary Encoders

Everight Position, a leading resource for rotary encoders is excited to announce the launching of NetzerUSA.com , an online resource dedicated to empowering control engineers in the United States.