Hazardous environment sensors are vital for ensuring safety and operational efficiency in extreme conditions. From explosive atmospheres to high-temperature or high-pressure environments, these sensors are designed to deliver reliable performance when it matters most. At Everight Position, we provide advanced solutions engineered to withstand the harshest conditions and meet stringent safety standards.
The intrinsically safe X117 is ATEX and IECEx approved for use in potentially explosive gas/vapour atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.
Overall performance, repeatability and stability are outstanding over a wide temperature range. The unit is very compact and space-efficient with a small 19mm diameter body. The sensor is very robust, the body and push rod being made of stainless steel. The sensor is easy to install with mounting options including M5 male stud and M5 rod eye bearing. The push rod can be supplied free or captive, with male M5 thread or M5 rod eye. Like all Positek sensors, the X117 provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-350mm and with full EMC protection built in. The X117 offers a range of mechanical options, environmental sealing is to IP67.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
The intrinsically safe M100 is ATEX and IECEx approved for use in potentially explosive gas/vapour, dust atmospheres and mining environments. It is designed for demanding hydraulic or pneumatic cylinder position feedback applications where service life, environmental resistance and cost are important and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.
Overall performance, repeat-ability and stability are outstanding over a wide temperature range. The unit is highly compact and space-efficient, being responsive along almost its entire length. Like all Positek sensors, the M100 provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in.
The sensor is very rugged, being made of stainless steel with an inert fluoropolymer-sheathed probe and stainless steel target tube. The sensor is easy to install in cylinders and has a wide range of mechanical options. Environmental sealing is to IP65 or IP67 depending on selected cable or connector options.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
The MR341 Mini Rotary Encoder is a Size 11, small form factor incremental encoder offering resolution to 512ppr. It is inter-mountable with resolvers, synchros and conventional electronic-based encoders of the same size. The MR341 Encoder is a 100% passive sensor which operates entirely in the optical domain. The sensor provides immunity to any electro-magnetic interferences such as lightning, radiation, magnetic fields and other harsh environment conditions. The innovative design provides 100% electrical isolation as well as immunity to high voltages ideal for harsh environment applications such as feedback for welding robots, measuring anode position in smelters, and monitoring pantograph operation in electric rail applications.
The intrinsically safe M500 is ATEX and IECEx approved for use in potentially explosive gas/vapour, dust atmospheres and mining environments.
It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.
The M500, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 16 and 160 degrees and with full EMC protection built in. The sensor provides a linear output proportional with angle of rotation. There is a machined registration mark to identify the calibrated mid point.
Overall performance, repeatability and stability are outstanding over a wide temperature range. The M500 has long service life and environmental resistance with a rugged stainless steel body, shaft, flange or servo mount. The flange or servo mounting options make the sensor easy to install, it also offers a range of mechanical options. Environmental sealing is to IP67 .
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
The intrinsically safe E112 is ATEX and IECEx approved for use in potentially explosive gas/vapour and dust atmospheres. It is designed for gauge head positioning in industrial and scientific applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas. The E112, like all Positek sensors, provides a linear output proportional to displacement. Each sensor is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-50mm and with full EMC protection built in.
Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is very robust, the body and plunger being made of stainless steel for long service life and environmental resistance.
The plunger is spring loaded with a domed end. The E112 is easy to install with a long ½ inch UNF mounting thread and is supplied with two lock nuts for positioning. Environmental sealing is to IP67.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
The G005 Galvanic Isolation Amplifier has been designed specifically for use with Positek Intrinsically Safe position sensors in hazardous Zone 0, 20 Class I, II & III applications and is certified; [Ex ia IIC] [AEx ia IIC] [AEx iaD IIIC]. The Amplifier sacles the output in the safe area and ensures the corresponding output is correct over a wide range of input voltages. It also supports a 5-wire installation option which can negate the effect of losses over long distances, thus maintaining the output signal accuracy. The X005 is factory configured to either 0.5 to 9.5V or 4-20mA and has a bandwidth of 4.7kHz.
The intrinsically safe M133 is ATEX and IECEx approved for use in potentially explosive gas/vapour, dust atmospheres and mining environments. It is designed for a wide range of industrial applications and is ideal for OEMs seeking good sensor performance in situations where a mid-bodied sensor is required for operation in hazardous areas. The unit is compact and space-efficient, being responsive along almost its entire length, and like all Positek sensors provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-51mm to 0-100mm and with full EMC protection built in.
Overall performance, repeatability and stability are outstanding over a wide temperature range.
The sensor has a rugged stainless steel body and plunger. It is easy to install and set up, mounting options include flange and body clamps. The plunger can be supplied free or captive, with female M4 thread, or spring-loaded with a ball end. The M133 also offers a wide range of mechanical options, environmental sealing is to IP65 or IP67 depending on selected cable or connector options.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier. Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
The intrinsically safe M117 is ATEX and IECEx approved for use in potentially explosive gas/vapour, dust atmospheres and mining environments. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.
Overall performance, repeatability and stability are outstanding over a wide temperature range. The unit is very compact and space-efficient with a small 19mm diameter body. The sensor is very robust, the body and push rod being made of stainless steel. The sensor is easy to install with mounting options including M5 male stud and M5 rod eye bearing. The push rod can be supplied free or captive, with male M5 thread or M5 rod eye. Like all Positek sensors, the M117 provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-350mm and with full EMC protection built in. The M117 offers a range of mechanical options, environmental sealing is to IP67.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
Choosing the correct sensor for hazardous environments is critical to maintaining safety, compliance, and performance. Here are the essential factors to consider:
By carefully evaluating these criteria, you can select a hazardous environment sensor that ensures safety, compliance, and optimal performance in your application.
Our hazardous environment sensors are trusted across industries to provide safety and performance in challenging conditions, including:
Monitor pressure, temperature, and flow in refineries, pipelines, and offshore platforms.
Ensure safe operations in facilities handling volatile or corrosive chemicals.
Optimize safety and performance in underground operations and drilling rigs.
Comply with safety standards in environments with combustible dust or extreme temperatures.
Enhance monitoring in environments with high heat and pressure, such as turbines and boilers.
Everight Position offers a diverse range of sensors engineered for hazardous environments. Our product line includes:
Designed to contain and isolate potential ignition sources.
Reduce energy output to prevent ignition in flammable atmospheres.
Built to withstand exposure to aggressive chemicals.
Capable of performing reliably in extreme heat conditions.
Measure multiple parameters like temperature, pressure, and vibration simultaneously.
Tailored sensors designed to meet specific application challenges.
Our sensors combine durability and precision, ensuring they meet the demands of even the most extreme environments.
At Everight Position, we understand the complexities of working in hazardous conditions. Our team of experts is here to help you select, implement, and maintain the ideal sensors for your needs. We provide:
Trust Everight Position for advanced hazardous environment sensor solutions that prioritize safety, compliance, and reliability. Contact us today to explore our product offerings and discover how we can help protect your operations.
Have questions or need help finding the right solution? Our team is ready to assist.
"*" indicates required fields