Positek

E603

Part no.: E603

Key Features

• Single axis

• Up to 160°

• Voltage or Current interface

• IP67

The intrinsically safe E603 is ATEX and IECEx approved for use in potentially explosive gas/vapour and dust atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

The E603, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees and with full EMC protection built in. The sensor provides a linear output characteristic with angle of deflection. There is a machined registration mark to identify the calibrated mid point.
Overall performance, repeatability and stability are outstanding over a wide temperature range. Electrical connections to the sensor are made via an industrial standard 4-pin M12 connector, with limited rotational capability to facilitate cable routing. The sensor has a rugged stainless steel body and mounting flange. The flange has two 4.5mm by 30 degree wide slots on a 48mm pitch to simplify mounting and position adjustment. Environmental sealing is to IP67.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Call us for more info at 856-727-9500

  • Hi, My name is

  • and I’m interested in the

  • You can reach me by email at

  • or phone at

  • Message

  • This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

X125

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800mm
  • Sealed to IP68 350bar, 3500msw, 5000psi

Positek

E117

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
  • Available in any measurement range from 0-5mm to 0-350mm
  • Sealed to IP67

Positek

S623

  • Single axis
  • Up to 160°
  • Voltage, Current or Ratiometric interface
  • IP67

Positek

Positek E500

  • ATEX/IECEx for gas/vapor and dust
  • 0.5-9.5V or 4-20mA outputs
  • ATEX variants of P502 & P505 available
  • Up to 160 deg range
Blog:

Absolute Rotary Encoders Available with BiSS-C Interface

POSITAL’s magnetic absolute rotary encoders are now available with the BiSS-C interface. These products are available in a wide range of mechanical configurations include a 36mm…

NEW PRODUCT – VLH-35 ELECTRIC ENCODER FOR DC SERVO MOTORS

Netzer Precision Position Sensors is introducing the VLH-35, a new product designed to meet the needs of the servo motor industry and its requirements for the next generation of industrial rotary motion control.

Dynamic Inclinometers

For applications where sudden movements, shocks, and vibrations are likely to be encountered, it is important to have sensors with fast response and a clean signal output. POSITAL’s dynamic inclinometers combine two measurement principles using two different MEMS sensors: a 3D acceleration sensor and a 3D gyroscope.

Spine Surgery Robot

Spinal surgery robot with advanced robotic guided technologies supports high requirements of predictable surgical procedures.