H100

Positek

Part no.: H100

Key Features

• CSA approved to: Class I, Zone 0

• Sensor Mounting: In-Cylinder Mounting

• Any stroke from 0-5mm to 0-800mm (e.g. 305mm)

• IP65 (connector) / IP67 (cable)

The intrinsically safe H100 is CSA approved for use in potentially explosive gas/vapour and dust atmospheres. It is designed for demanding hydraulic or pneumatic cylinder position feedback applications where service life, environmental resistance and cost are important and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.

Overall performance, repeat-ability and stability are outstanding over a wide temperature range. The unit is highly compact and space-efficient, being responsive along almost its entire length. Like all Positek sensors, the H100 provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in.

The sensor is very rugged, being made of stainless steel with an inert fluoropolymer-sheathed probe and stainless steel target tube. The sensor is easy to install in cylinders and has a wide range of mechanical options. Environmental sealing is to IP65 or IP67 depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (G005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Datasheet Download

Part Builder

Drawing Download

Call us for more info at 856-727-9500

"*" indicates required fields

You may also be interested in:

Positek

P106

Probe Head Diameter: 20mmElectronics Module: 35mm
Sensor Mounting: In-cylinder
Available in any measurement range from 0-5mm to 0-800mm
Sealed to IP65/67 depending on connector/cable option

Positek

X120

ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
Sensor Mounting: M18 or 3/4" UNF threadTarget tube flanges available
Available in any measurement angle from 0-5mm to 0-800mm
Sealed to IP68 350bar, 3500msw, 5000psi(combined hydraulic and water pressure)

Positek

G101

CSA approved to: Class I, Zone 0
Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
Sealed to IP65/67 depending on connector/cable option

Positek

G111

CSA approved to: Class I, Zone 0
Sensor Mounting: M8 Rod Eyes, Body Clamps or M8 ThreadsSpring loaded pushrod option available
Available in any measurement range from 0-5mm to 0-800mm
Sealed to IP65/67 depending on connector/cable option

Dynamic Inclinometers

For applications where sudden movements, shocks, and vibrations are likely to be encountered, it is important to have sensors with fast response and a clean signal output. POSITAL’s dynamic inclinometers combine two measurement principles using two different MEMS sensors: a 3D acceleration sensor and a 3D gyroscope.

SSI Encoder

Synchronous Serial Interface (SSI) is a widely used serial interface standard for industrial applications between a master (i.g. controller) and a slave (i.g. sensor).

Submersible Linear Sensors

Positek’s portfolio includes a range of high-accuracy linear sensors specifically designed for use in submersible applications. Made from marine grade stainless steel and offering the reliability that is not possible from a submersible LVDT or linear potentiometer, our sensors have served a host of different industries such as wastewater and offshore oil drilling. Another use […]