Positek

H111

Part no.: H111

Key Features

• CSA approved to: Class I, Zone 0

• Sensor Mounting: M8 Rod Eyes, Body Clamps or M8 ThreadsSpring loaded pushrod option available

• Available in any measurement range from 0-5mm to 0-800mm

• Sealed to IP65/67 depending on connector/cable option

The intrinsically safe H111 is CSA approved for use in potentially explosive gas/vapour and dust atmospheres. This heavy-duty version of the H101 sensor with a stronger 12.6mm push rod, recommended for applications where vibration is an issue or there is a need for longer travel sensors, mounted horizontally, and supported between rod eyes. It remains an affordable, durable, high-accuracy position sensor designed for industrial and scientific feedback applications. The unit is highly compact and space-efficient, being responsive along almost its entire length. Like all Positek sensors, the H111 provides a linear output proportional to displacement. Each sensor is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in.

The sensor is very robust, the body and push rod being made of stainless steel for long service life and environmental resistance. Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with mounting options including M8 rod eye bearings and body clamps. The push rod can be supplied free or captive, with female M8 thread, an M8 rod eye, or dome end, Captive push rods can be sprung loaded, in either direction, on sensors up to 300mm of travel. Environmental sealing is to IP65 or IP67, depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (G005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Call us for more info at 856-727-9500

  • Hi, My name is

  • and I’m interested in the

  • You can reach me by email at

  • or phone at

  • Message

  • This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

X115

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M8 rod eyes, body clamps or M8 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800m
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Positek

X114

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M5 rod eyes, body clamps or M5 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800mm
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Positek

E114

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: M5 rod eyes, body clamps or M5 threadsSpring loaded pushrod option available
  • Available in any measurement angle from 0-5mm to 0-800mm
  • Sealed to IP68 10bar, 100msw, 145psi(for 350bar sealing see S125)

Positek

P118

  • Body Diameter: 19mm
  • Sensor Mounting: Flange or body clampsSpring loaded pushrod option available
  • Available in any measurement range from 0-2mm to 0-50mm(for 51-100mm range see P138)
  • Sealed to IP67
Blog:

UAV Tank Level Measurement

For maximum endurance and payload transportation capacity many UAV manufacturers turn to ICE (Internal Combustion Engine) powered flight. Electric propulsion has its place, but for maximum energy density batteries are not currently at the level of modern fossil fuels.

Introduction to Intrinsically Safe Sensors

Intrinsically safe sensors and systems are used to provide a safe operating environment for personnel and equipment. They do this by restricting the electrical energy transmitted into a hazardous area.

Redundant Encoder Options

While most modern rotary encoders rely on non-contact sensing technologies and have high MTBF specifications, in critical applications it is still common to have redundant sensors required. When selecting a solution, a number of different criteria need to be considered and fortunately different solutions exist, making the task less daunting. Redundancy One of the first […]

Implementation of SSI Interface

Synchronous Serial Interface (SSI) is a widely used serial interface standard for industrial applications especially, rotary encoders. It is a point-to-point connection from a master (e.g. PLC, microcontroller or other control systems) to a slave (e.g. the rotary encoder).