Positek

G101

Part no.: G101

Key Features

• CSA approved to: Class I, Zone 0

• Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available

• Any stroke from 0-5mm to 0-800mm (e.g. 305mm)

• Sealed to IP65/67 depending on connector/cable option

The intrinsically safe G101 is CSA approved for use in potentially explosive gas/vapour atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas. The unit is highly compact and space-efficient, being responsive along almost its entire length.

The G101, like all Positek sensors, provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-5mm to 0-800mm and with full EMC protection built in. The sensor is very robust, the body and push rod being made of stainless steel for long service life and environmental resistance.

Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor is easy to install with mounting options including M5 rod eye bearings and body clamps. The push rod can be supplied free or captive, with female M5 thread, an M5 rod eye, or dome end, Captive push rods can be sprung loaded, in either direction, on sensors up to 300mm of travel. Environmental sealing is to IP65 or IP67, depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (G005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Call us for more info at 856-727-9500

  • Hi, My name is

  • and I’m interested in the

  • You can reach me by email at

  • or phone at

  • Message

  • This field is for validation purposes and should be left unchanged.
You may also be interested in:

Positek

X130

  • ATEX/IECEx approved to: Ex II 1G : Ex ia IIC T4 GA (Ta = -40°C to +80°C)
  • Sensor Mounting: In-cylinder
  • Available in any measurement range from 0-400mm to 0-1485mm
  • Sealed to IP65/67 depending on connector/cable option

Positek

Positek S508

  • Subsea encoder to 10 Bar, IP68, IP69K
  • Analog voltage and current outputs
  • Up to 0.1% linearity
  • Measure up to 160 deg range

Positek

G603

  • Single axis
  • Voltage or Current interface
  • IP67

Positek

P101

  • Body Diameter: 35mm
  • Sensor Mounting: M5 Rod Eyes, Body Clamps or M5 ThreadsSpring loaded pushrod option available
  • Any stroke from 0-5mm to 0-800mm (e.g. 305mm)
  • Sealed to IP65/67 depending on connector/cable option
Blog:

SSI Encoder

Synchronous Serial Interface (SSI) is a widely used serial interface standard for industrial applications between a master (i.g. controller) and a slave (i.g. sensor).

Introduction to Intrinsically Safe Sensors

Intrinsically safe sensors and systems are used to provide a safe operating environment for personnel and equipment. They do this by restricting the electrical energy transmitted into a hazardous area.

Netzer Electric Encoder Explorer Software

Get started with Netzer Electric Encoder Explorer Ready to learn how to get started with Netzer Electric Encoder Explorer? We can help!  Take a look at this video where we walk you through the software and teach you the ins and outs of the Netzer Electric Encoder Explorer.  Start with Signal Amplitude One of the […]

UAV Tank Level Measurement

For maximum endurance and payload transportation capacity many UAV manufacturers turn to ICE (Internal Combustion Engine) powered flight. Electric propulsion has its place, but for maximum energy density batteries are not currently at the level of modern fossil fuels.